Konten Lembar Data
PROF 02
User’s manual - Use and Maintenance E
Descaling pumps
Dear Customer, thank you for choosing a EUROACQUE Pump.
MANUAL
This manual is a safe guide for the use of the pump. Please read it carefully in all its parts before use.
This manual contains important information for the proper working and use of the equipment.
EUROACQUE reserve the right to introduce any future changes without notice or replacement.
PRELIMINARY INSPECTION
Upon receipt of the pump, take it out from the carton and check it is in perfect condition. Also check
that the data on the rating plate correspond to required ones. For any problem, immediately contact
the supplier specifying the kind of fault.
In case of doubts about the safety of the machine, do not use it.
DESCRIPTION
The pump SUPERFLUK is fitted with built-in heater and flow reverser. Particularly
recommended for difficult descaling treatments, they work in complete safety and autonomy
enabling the operator to carry out other works at the same time.
Pumps with tank for descaling boilers by using specific acid based restoring products.
The pumps are equipped with special fittings and valves to adjust the flows and purge the sludge, built
up by the operation, which is then rapidly removed.
Pumps are supplied ready to use, in strong carton boxes with related user’s manual.
CONTENTS
1 - REGULATIONS – CE MARK page 2
2 - THE ADVANTAGES OF THE PUMPS PROF 02 page 2
3 - TECHNICAL FEATURES page 3
4 - CUSTOMER SERVICE page 3
5 - USE page 3
6 - SAFETY INSTRUCTIONS page 4
7 - EXPLODED VIEWS page 5
8 - DIRECTIONS FOR DISPOSAL page 6
9 - WARRANTY TERMS AND AFTER-SALE ASSISTANCE CONDITIONS page 6
1
1 - REGULATIONS – CE MARK
Declaration of Conformity
The pumps are in conformity with the following European Directives, Laws and Regulations:
Machinery Directive 2006/42/EC
QUALITY
EUROACQUE equipments are manufactured with high-quality acid-resistant materials and
submitted to severe operating tests.
Follow these instructions to avoid any operating and servicing problems.
2 - THE ADVANTAGES OF THE PUMP SUPERFLUK
Time and, above all, temperature increase make
calcium salts, usually present in water, precipitate in the Heat exchanger
form of microcrystals and settle on metallic surfaces of
pipes, plant coils and heat exchangers, thus reducing
flow rate and thermal efficiency.
To restore the original plant performance it is necessary
to carry out a descaling with specific products and
equipments.
The built-in heater and flow reverser device attacks
scale on both sides, thus making descaling particularly
effective and fast (as the normal dissolving action is
combined with the detachment in flakes of scale, which
is made friable by the double attack), even when pipes
and exchangers are almost totally obstructed.
Thermo-Clean
Clockwise Counterclockwise
circulation circulation
2
3 - TECHNICAL FEATURES
SUPERFLUK
Motor 220V, 600W - HP 0,8
Max working pressure 6 Bar
Degree of protection IPX4
Max. temperature 60° C
Flow rate 50* l/min.
ENGLISH
Head 60m*
Fittings 3/4”
Tank capacity 35 l
Heating coil 2000 w
Flow Reverser Manual
Dimensions HxWxD 65 x 35 x 40 cm
Weight Kg 23
* Data referred to the pump body outlet.
4 - CUSTOMER SERVICE
For enquiries on spare parts, please specify serial number of pump (shown on product and
carton).
5 - USE
5.1 - HOW TO PREPARE THE PUMP AND CHECK THE SEAL
- Fill the tank with enough water to ensure that the pump rotor
housing is submerged during operation.
- Screw the outer ends of the flexible hoses securely to the
exchanger to be descaled.
- Connect the power cable to a single-phase 220 V power
supply.
- Switch on the pump and check the seal of the hose fittings on
the exchanger and on the pump. In case of leaks of liquid,
check hoses and fittings and replace the defective
components, if necessary.
- When seal is safe, switch off the pump. FLOW
RETURN
FLOW
RETURN
- If necessary, add more descaling product by referring to the
dilution specified in the data sheet of the product.
3
5.2 - FUNCTIONING
Connect pump to the system.
Ensure that valve is in the closed position.
-Fill the tank with water.
-Add cleaning chemical to the tank.
-Turn on the heater. SUPERFLUK have automatic temperature controller on it. Heater
automaticaly heats water up to 50° C in the tank.
-Switch on the pump and clean the system.
-Use flow reverser for efficient cleaning.
The SUPERFLUK have 2 x 250 cm flow/return hoses fitted with
3/4” brass hose connectors at the out board end and 3/4” fittings at the inboard end.
In cleaning process:
The inboard end of both flow/return hoses should be screwed onto the corresponding
¾” brass nipples on rear of the hose support plate. The other ends of these hoses should be
connected to the system (radiator/boiler/pump).
In dumping process:
Disconnect one of the flow/return hose screwed on rear of the hose support plate and lead
it to a toilet pan or drain pipe g ully leading to a foul sewer.
5.3 - HOW TO CLEAN THE PUMP
After descaling REMOVE THE DESCALING LIQUID FROM THE TANK and wash out the pump by
circulating clean water through it for at least 10 minutes.
ADD 200 cc. OF XS2 PRODUCT FOR THE MAINTENANCE AND CLEANING OF THE IMPELLER
6 - SAFETY INSTRUCTIONS
- Avoid using the pump in rooms where there are liquids, gases, flammable powders or with risk of
explosion.
- Before plugging in the pump to the outlet, make sure the switch is off.
- The outlet must be suitable for the plug of the pump. Do not use non CE-marked defective outlets.
- Use (CE) approved extensions, only if necessary.
- Do not use plug adapter. Do not carry out any modifications to the plug nor to the electrical cable.
- Pump shall always kept in perfect efficiency.
- During maintenance operations, check the switch is off and the plug is not connected.
- All maintenance operations must be carried out by the authorized Technical Assistance Service.
- Only use EUROACQUE original spare parts.
- Do not carry out any modifications to the pump if not authorized by Technical
Department (ask for written authorization).
- Keep children and unauthorized persons away from the pump.
- Keep the pump out of reach of children and unauthorized persons.
- Do not use the pump if tired or under the effect of alcohol, medicines or drugs.
- When using the pump, wear overalls, do not wear jewellery, keep hair away from the pump.
- When handling descaling liquids, be very careful. It is necessary to use Individual Protection
Equipment (IPE).
4
7 - EXPLODED VIEWS AND SPARES DIAGRAMS
P.S..: For enquiries on spare parts, please specify always if needed for the model
SUPERFLUK
1
3
2 15 16 17
4
5 9
11 13
18
6
19
20
10
12 21
14
7 25 26
8
22 27
23
28
24 29
1. Filter 10. Connection hose 1/2" 19. Electric cable 28. Electric cable
2. Tank 11. 2 way connector 3/4" 20. 4 way ball valve 29. Flow-return outlet 3/4"
3. Tank cap 12. Elbow 3/4" 21. Back&bottom metal panel 30. Heater switch on/off
4. Elbow 13. Pneumatic hose 22. Pressure indicator 31. 3/4” Pressure line
5. Thermostat 14. Pump 23. Flow reverser valve 32. Cap
6. Heating element 15. Heat meter 24. Flow-return outlet 3/4" 33. Heater switch on/off
7. Elbow 1/2" 16. Pump switch 25. Pump on/off switch 7. Temperature indicator
8. Wheel 17.Heater switch 26. Heater on/ff switch 8. 3/4” Return line
9. Connection hose 1/2" 18.Pressure gauge 27. Temperature indicator 9. Wheel
5
8 - DIRECTIONS FOR DISPOSAL
In accordance with the WEEE directive 2002/96/EC on waste electrical and
electronic equipment, the pump, when no longer used, shall be disposed of in a
RAEE – WEEE collection centre authorized for disposal of waste electrical and
electronic equipment, or directly contact your dealer.
9 - WARRANTY TERMS AND AFTER-SALE ASSISTANCE CONDITIONS
EUROACQUE guarantee that the equipments sold are free from designing, manufacturing and
material defects, under normal operating conditions and according to the directions contained in
the instruc- tions manual supplied with the equipment.
In compliance with the directive 1999/44/CE valid in the EEC countries, the warranty rights apply only
to the purchaser.
EUROACQUE guarantee the equipments against any conformity defects appearing within 12…
