Suntec PUMP T

[{"filename":"T_EN_Ed20_January-2025.pdf","text":"PUMP TYPE T T\n T - 11 - Ed 20 - January 2025\nThis is a general specification leaflet ; for specific applications not covered herein,\n PUMP\ncontact Suntec.\n IDENTIFICATION\nThe SUNTEC T oil pump is specially designed for industrial heating applications (Not all model combinations are available\nusing light or heavy oils with high capacity. It is fitted with a preheater location to Consult your Suntec representative)\nrender cold starting easier.\n\nCOMPATIBILITY\n- Domestic oil, HVO, B100. T : No pressure regulation\n- SUNTEC recommend the use of a SUNTEC TV valve to regulate the pump\n pressure.\n Gear set capacity\nPUMP OPERATING PRINCIPLE (see pump capacity curves)\n\nThe gear set draws oil from the tank and transfers it to an external valve that\nregulates the oil pressure.\n Shaft rotation\nBleed (seen from shaft end)\nThe plug of the pressure gauge port must be loosened until the air is evacuated A : clockwise rotation / left\n hand nozzle\nfrom the system.\n C : anti clockwise rotation /\nNote right hand nozzle\n\nThe bypass plug inserted between high pressure and shaft seal is only intended to\nchange the pump rotation, check the presence of this plug with a 4 mm Allen key\n T 2 A 10 7\nin the pressure outlet of the pump.\nCaution : changing the direction of pump rotation involves changing all pump\nconnections.\nPREHEATING FACILITY\nCare should be taken to avoid starting pump with high viscosity cold oil leading to\npump and coupling damage. For this reason, the T pump body includes a cavity to Preheater facility\naccept an electric preheater. This cavity has been located to give maximum heat\ntransfer from the heater to the oil in the pump without direct contact between the\nheater cartridge and the oil. Revision number\n\nHeaters should be connected for a period of time prior to starting the pump. When the\nright temperature is reached, they can be switched off or left permanently switched\non to maintain fluid oil in the pump during the periodic burner shut-downs.\nThe oil supply, pipes and filters must be separately heated.\n\n\n\n\n Plug inserted between\n Oil under suction\n high pressure and shaft seal\n To\n Oil under pressure pressure regulating\n valve\n\n Vacuum or\n inlet pressure Pressure\n gauge port gauge port\n\n\n\n\n To\n Intake pressure\n from Tank regulating\n valve\n\n\n\n\n Intake\n from Tank\n\n SUNTEC INDUSTRIES FRANCE - 1, rue Lavoisier - CS 60 102 - F-21603 LONGVIC Cedex - www.suntec.fr\n\fTECHNICAL DATA Pump capacity\n Capacity (L/h)\n\nGeneral\n\nMounting Flange mounting\nConnection threads Cylindrical according to ISO 228/1\nInlet G 3/4\nPressure outlet G 3/4\nPressure gauge port G 1/4\nVacuum Gauge port G 1/4\nShaft Ø 20 mm\nWeight 7,8 kg (T2) - 8,1 kg (T3)\n 8,7 kg (T4) - 9,4 kg (T5)\n\n\nHydraulic data\n Pressure (bars)\nNozzle pressure range 40 bars max. (T2, T3, T4)\n 30 bars max. (T5) Viscosity = 75 cSt\n 20 cSt\nOperating viscosity 2 - 75 mm²/s (cSt) 5 cSt - Rated speed = 2850 rpm\n\n(Higher viscosity oil can be used by feeding the pump and by heating the oil to lower\n Data shown are for new pumps, with no allowance for wear.\nits viscosity under 75 cSt. For kerosene applications, contact SUNTEC).\nOil temperature 0 - 150°C in the pump Power consumption\nInlet pressure light oil : 0,45 bars max. vacuum to prevent Power (W)\n air separation from oil.\n heavy oil : 5 bars max.\nRated speed 3600 rpm max.\nTorque (@ 40 rpm) 0,4 N.m\n\n\nChoice of heater\n\nCartridge Ø 12 mm\nFitting according to EN 50262\nRating 80-100 W\n Pressure (bars)\n Viscosity = 75 cSt\n 5 cSt - Rated speed = 2850 rpm\n\n Data shown are for new pumps, with no allowance for wear.\n\n\n PUMP DIMENSIONS (in mm) Example shows pump with “A” rotation and serial number ≥ 50 000. -\n Reverse all pump connections for “C” rotation.\n T2 T3 T4 T5\n 150\n A 68 73 78 87\n (mm) 132\n 68 19 19\n 33  \n\n B\n\n Ø70 Ø11\n\n 132\n B  \n Ø19 min\n 85 6 M16x1,5\n\n\n 22,5\n\n  Ø20 1,5 max\n 8 min\n B-B 90\n 12 min Ø12,1 min Ø11\n 36 A 71,5 min\n\n\n\n\n Pressure outlet and Vacuum or Pressure Preheater\n  Suction  internal by-pass plug  inlet pressure gauge port  gauge port  cavity\n\n\nWe reserve the right to change specifications without prior notice. T - 11 - Ed 20 - Jan 2025"}]