DSZH Adjustable digital torque wrench

Digital Electronic Torque Wrench Operating Manual Model 60648 This manual will help you to use the many MAINTENANCE AND STORAGE features of your new digital torque wrench. Before operating the torque wrench, please read ATTENTION: this manual completely, and keep it nearby for To maintain accuracy, a one-year future reference. periodic recalibration is recommended. Please contact your local dealer for calibration details. FEATURES CAUTION: 1. Over-torque (110% of ● Interchangeable head Max. torque range) ● Digital torque value readout could cause breakage ● +/- 2% accuracy or loss of accuracy. ● CW and CCW operation 2. Do not shake violently ● Peak hold and track mode selectable or drop wrench. ● Buzzer and LED indicator for the 9 pre-set 3. Do not use the wrench target torques as a hammer. ● Water contact indicator 4. Do not leave the wrench in any place exposed to ● Engineering units (ft-lb, in-lb, N-m, kg-cm) excessive heat, humidity, or direct sunlight. 5. Do not use the wrench in water (not waterproof). selectable 6. If the wrench gets wet, wipe it with a dry towel ● Stores up to 50 data files for recall and joint as soon as possible. The salt in seawater can be torque auditing especially damaging. ● Auto Sleep after about five minutes idle 7. Do not use organic solvents, such as alcohol or ● (2) AAA Batteries included paint thinner when cleaning the wrench. 8. Keep the wrench away from magnets. 9. Do not expose the wrench to dust or sand as this could cause serious damage. 10. Do not apply excessive force to the LCD panel. 11. Apply torque slowly and grasp the center of the handle. Do not apply load to the end of the handle. BATTERY MAINTENANCE 1. When the wrench is not used for an extended period of time, remove the battery. 2. Keep a spare battery on hand when going on a long trip or to cold areas. 3. Do not mix battery types or combine used batteries with new ones. 4. Sweat, oil and water can prevent a battery’s terminal from making electrical contact. To avoid this, wipe both terminals before loading a battery. 5. Dispose of batteries in a designated disposal area. Do not throw batteries into a fire. 2 NAMES AND FUNCTIONS OF PARTS 1 2 3 4 5 6 7 8 9 10 11 12 14 15 13 16 17 18 1. Head Insert 10. Anti-Slip Handle 2. Sensor Yoke 11. Jaw Adjuster 3. LCD Readout 12. Battery Cover 4. Communication Part 13. LED Indicator 5. UP/DOWN Button 14. Torque Value 6. Buzzer 15. Units (ft-lb, in-lb, N-m, 7. Power ON/CLEAR Button kg-cm) 8. Unit/Setting Button 16. Pre-Setting Number 9. Pre-setting Number 17. Peak/Track Mode Selection Button 18. Water Indicator Viewing Window 3  BEFORE USING THE WRENCH SPECIFICATIONS BEFORE USING BEFORE USING THE WRENCH BATTERY INSTALLATION BATTERY INSTALLATION Model Max. Square Torque Length  Remove the battery cover. Torque Drive Measuring No. (inches) Range  Insert  Remove twothe AAA batteries battery cover.matching the -/+ polarities  Insert two AAA of batteries the battery to the battery matching the 60648 62.7 ft. lb. 3/8 3.1-62.7 ft. lb. 10.6 in. compartment. -/+ polarities of the battery to the battery 85 N-m 4.2~85 N-m 270 mm  Replace the compartment. battery cover and fasten it tightly All Models  according Replace the tobattery the following figures. cover and fasten it tightly according to the following figures. Accuracy *1 CW：±2% Cover CCW：±3% Cover Data memory test 50 Pre-Sets 9 6LEDs Battery Bright LED (1 Red+5 Green) Battery Operation Mode Peak hold/Track Unit Selection ft-lb, in-lb (N-m, kg-cm) Gear Teeth 52 Button 5 ATTENTION: ATTENTION: Battery AAA x 2 (included) When opening the battery cover of your wrench, ATTENTION: Operating Temperature 14οF ~ 140οF (-10℃ ~ 60℃) you Whencanopening see a viewing window the battery coverfor ofthe water your wrench, contact you can indicator. Through see a viewing windowthisfor viewing the water Storage Temperature 4οF ~ 158οF (-20℃ ~ 70℃) window, you can check if the wrench contact indicator. Through this viewing is damaged by water window, you penetration can check (the water if the wrench is Humidity Up to 90% non-condensing contact damagedindicator by waterturns red). (the water penetration Drop Test 1m contact indicator turns red). Vibration Test *2 10G POWER ON AND RESETTING THE WRENCH Environmental Test *3 Pass POWER ON AND RESETTING THE WRENCH Environmental Test *4 Pass  Press to power on the digital torque wrench. Presscan press  You…