DUNGS CP 9302-702 - Actuator Drive (US/CA)

[{"filename":"cp-9302-702_manual_us_261484.pdf","text":"CP-9302-702\n Actuator Drive USA CDN\n Installation Instructions\n\n\n\n Table of Contents\n Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . Page 1\n Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1\n Attention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1\n Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2\n Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2\n Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3\n Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4\n Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5\n Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6\n Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6\n\n\n\n\n Approvals\n UL Listed: UL 873\n\n\n\n\n Attention\n The installation and maintenance On completion of installation\n of this product must be done Safety on the CP-9302-702, perform a\n under the supervision of an ex-\n first function test.\n\n\n O.K.\n perienced and trained specialist.\n Never perform work if gas pres-\n sure or power is applied, or in\n the presence of an open flame.\n\n Please read the instruction be- This product is intended to be\n fore installing or operating. Keep IFGC used in combination with a con-\n the instruction in a safe place. You CSA trol valve to modulate the flow of\n UL\n\n\n\n\n MC • Karl Dungs, Inc. • CP-9302-702 • Edition 2016.02 • P/N 261484\n find the instruction also at www. gas or air.\n dungs.com If these instructions ANSI\n are not heeded, the result may NFPA\n be personal injury or damage to\n property.\n Any adjustment and application-\n specific adjustment values must\n be made in accordance with\n the equipment manufacturers\n instructions.\n\n\n\n\n Explanation of symbols\n 1, 2, 3 ...\t = Action\n • = Instruction\n1…6\n\f Specification\n CP The CP-9302-702 electronic actuator drive processes a variable input signal from a controller to provide\n proportional control of an electric actuator. The CP-930-702 is preset for current input (4 - 20 mA) and has\n additional wiring for connection to an override switch for applications requiring an external override of the\n input signal. The CP-9302-702 is equipped with built in jumpers and adjustable potentiometers, so that the\n type of input signal, deadband, input span, and start point may be readjusted in the field when necessary.\n\n Electrical Ratings Ambient Temperature\n Power supplied by the actuator °F -40 °F to +160 °F (-40 °C to + 71 °C)\n +160\n Input: 4 - 20 mA\n Electrical Connection\n 0\n [V] [A] 1/2” NPT conduit knockout\n -40\n [Hz] [VA] Deadband Adjustability (Hysteresis)\n Factory set at 5 %, adjustable to 3 %\n Grounded Input\n Grounding either or both input wires\n will not cause damage\n\n\n\n\n Enviroment Series Operation\n NEMA Type 4 (weathertight) No offset in control point when oper-\n ated in tandem\n\n\n NEMA\n\n\n Open circuit Input\n Drives actuator to low\n\n\n\n\n Mounting\n 1) Inspect unit before installing, look for bent or broken parts\n or oil leaks from actuator.\n 2) Use NEAM Type 4 compatible type connectors.\n 3) Observe the barrier that separates the line voltage\n terminals from the low voltage which controls the actuator\n motor.\n 4) All connections to the line voltage side of the barrier (L1\n and L2, 1, 5 and 6 terminals) must be made with Class 1\n wiring; connections to the remaining terminals can be\n Class 2 thermostat cable if desired.\n 5) Allow 6 inches (152 mm) clearance above the actuator\n\n\n\n\n MC • Karl Dungs, Inc. • CP-9302-702 • Edition 2016.02 • P/N 261484\n wiring compartment.\n 6) Disconnect all power to the valves before wiring to prevent\n electrical shock and equipment damage.\n 7) Do not exceed the elctrical ratings given in the specifications\n and on the actuator.\n 8) Attach a felxible 1/2 conduit to the actuator.\n 9) Route the wires through the conduit.\n10) Use 14 or 16 guage wire for at least 75 °C (167 °F).\n11) Connect the wiring to the appropriate screw terminals.\n12) Remove the appropriate knock out on the side you wish\n to mount the sidebox.\n14) Insert the sidebox into the actuator and leaving the o-ring\n on the sidebox.\n15) Secure the sidebox to the actuator with the conduit locknut\n provided. 2…6\n\f Installation\n 1) Inspect unit before installing, look for broken parts or leaks. 4) Do not adjust the limit switch beyond 90° unless the\n Use NEMA Type 4 compatible type connectors. standard slidewire has been replaced with a 180° slidewire;\n do not adjust beyond 180° for proportioning control.\n 2) Observe the barrier that separates the…