Konten Lembar Data
[{"filename":"MAMP-1_MicroM_Amplifier_Modules_MEUV1_MEUV4_MEUVS1_MEUVS4_MEIR1_MEIR4_MERT1_MERT4_MECD1_MECD4_English_2013-04-03.pdf","text":"\n\n\n MAMP-1\n APRIL 3, 2013\n\n\n\n MEUV1, MEUV4,MEUVS1,\n MEUVS4, MEIR1, MEIR4,\n MERT1, MERT4,\n MECD1 and MECD4\n AMPLIFIER MODULES FOR USE WITH THE\n FIREYE® MODULAR 3G-OTH-02818™ CONTROL\n\n\n\n\n APPROVED\n\n\n\n\nDESCRIPTION\n The Fireye MEUV1, MEUV4, MEUVS1, MEUVS4, MERT1, MERT4, MEIR1, MEIR4, MECD1\n and MECD4 are Amplifier Modules used with the Fireye Modular 3G-OTH-02818 control. These amplifier\n modules provide flame scanning capabilities using any of the Fireye standard ultraviolet scanners,\n self-check scanners, infrared scanners, cadmium sulfide scanners and flame rods. The Flame Failure\n Response Time (FFRT) of the control is determined by the selection of the amplifier module (see\n Ordering Information). Test jacks are provided on the amplifier modules to permit flame signal mea-\n surement during operation and is a uniform 0-10 vdc for all models.\n After scanner selection, the proper amplifier module must be used in the Modular 3G-OTH-02818 chassis\n (see Ordering Information). The amplifier module incorporates a plug-in design for ease of installa-\n tion.\n The programmer module determines the operational characteristics of the control (e.g. relight, purge\n timing, etc.).\n For proper and safe application of this product, you must refer to bulletin MC-5000 for a detailed\n description of the operation of the Modular 3G-OTH-02818 control, including installation instructions,\n operating sequences for the programmer modules, etc. Also follow the scanner installation and wir-\n ing instructions found in bulletins MC-5000 for proper flame scanning operation.\n\n\n\n\n WARNING: Selection of this control for a particular application should be made by a com-\n petent professional, licensed by a state or other government agency. Inappropriate application\n of this product could result in an unsafe condition hazardous to life and property. Installation\n should not be considered complete until pilot turndown and other appropriate performance\n tests have been successfully completed.\n\n\n\n\n 1\n\f \n\n\n\n\nORDERING INFORMATION\nFlame Amplifier Selection:\n\n 3G-OTH-02818 Amplifier Models:\n MEUV1 UV amplifier,0.8 second FFRT, uses UV1A, UV2, UV8A and 45UV3-1050 scanners.\n MEUV4 UV amplifier, 4 second (max) FFRT, uses UV1A, UV2, UV8A and 45UV3-1050 scanners.\n MEUVS1 UV Self-Check amplifier,0.8 second FFRT, uses 45UV5-1009 scanner.\n MEUVS4 UV Self-Check amplifier, 4 second (max) FFRT, uses 45UV5-1009 scanner.\n MERT1 Flame Rod / Photocell amplifier,0.8 second FFRT, uses 69ND1 or 45CM1 (obsolete).\n MERT4 Flame Rod / Photocell amplifier, 4 second (max) FFRT, uses 69ND1 or 45CM1 (obsolete).\n MEIR1 Infrared amplifier0,.8 second FFRT, uses 48PT2 scanner.\n MEIR4 Infrared amplifier, 4 second (max) FFRT, uses 48PT2 scanner.\n MECD1 Cadmium sulfide amplifier,0.8 second FFRT, uses CS1A5 scanner.\n MECD4 Cadmium sulfide amplifier, 4 second (max) FFRT, uses CS1A5 scanner.\n\n\nFLAME SCANNERS\n\n\n\n\n CAUTION: The UV1, UV2, UV8A, UV90 and 45UV3 ultra-violet flame scanners and associated\n amplifier modules are non self-checking UV systems and should be applied only to burners that\n cycle often (e.g.: a minimum of once per 12 hours) in order for the safety checking circuit to be\n exercised. If component checking is required during burner operation for constantly fired burners,\n utilize the self-checking ultra-violet flame scanners (45UV5) with associated amplifier module\n (MEUVS1, MEUVS4) or the infrared flame scanner (48PT2) with associated Auto Check amplifier\n (MEIR1, MEIR4).\n\n UV SCANNERS: BULLETIN\n UV1A3 1/2” NPT connector, 3 ft. (914mm) TC-ER cable, non self-checking. SC-102\n UV1A6 1/2” NPT connector, 6 ft. (1828mm) TC-ER cable, non self-checking. SC-102\n UV2 3/8” NPT connector, 3 ft. (914mm) TC-ER cable, non self-checking. SC-102\n UV8A 1/2” NPT 90° head, 6 ft. unshielded leads. SC-102\n 45UV3-1050 3/4” sleeve/set screw mount. Non self-checking. SC-102\n 45UV5-1009 UV self-check scanner 8 ft. (2400mm) leads. 1” NPT threads. SC-101\n 120 VAC shutter. Use with MEUVS type amplifier.\n UV90-3 UV, 90° lateral view, 3 ft. (914mm) flex conduit SC-102\n UV90-6 UV, 90° lateral view, 6 ft. (1828mm) flex conduit SC-102\n UV90-9 UV, 90° lateral view, 9 ft. (2742mm) flex conduit SC-102\n\n FLAME DETECTORS: BULLETIN\n 45CM1-1000 Photocell with filter. OBSOLETE\n 45CM1-1000Y Photocell without filter. OBSOLETE\n 69ND1-1000K4 12 inch flame rod, 1/2” NPT connector. SC-103\n 69ND1-1000K6 18 inch flame rod, 1/2” NPT connector. SC-103\n 69ND1-1000K8 24 Inch flame rod, 1/2” NPT connector. SC-103\n\n\n2\n\f \n\n\n\n\n INFRARED SCANNERS: BULLETIN\n 48PT2-1003 Infrared scanner 8 ft. (2400mm) TC-ER cable, straight head. SC-103\n 48PT2-1007 Infrared scanner 4 ft. (1200mm) TC-ER cable, straight head. SC-103\n 48PT2-9003 Infrared scanner 8 ft. (2400mm) TC-ER cable, 90° head. SC-103\n 48PT2-9007 Infrared scanner 4 ft. (1200mm) TC-ER cable, 90° head. SC-103\n 48PT2-9007W Infrared scanner 4 ft. (1200mm) shielded cable, 90° head, water SC-103\n repellent. OBSOLETE, Replaced by 48PT2-9007\n\n CADMIUM SULPHIDE:\n CS1A5 Cadmium sulfide 5’, with mounting bracket\n\nParts and Accessories\n Part Number Description\n 4-263-1 Firetron cell for 48PT2 only.\n 4-314-1 UV tube for 45UV5-1005-1009, 45UV2, 45UV3.\n 10-88 Set of 3 orifice plugs (1/16'', 1/8'', 3/16'') for 48PT1, 48PT2.\n 19-30 Pyrex window for 60-801 union.\n 35-69 Heat insulator, 1/2\" connection for 48PT, UV1A.\n 35-75 Water cooled adapter for 48PT, UV1A.\n 35-127-1 Heat insulator. 1\" NPT for 45UV5.\n 46-38 Replacement lens (1.25\" dia.) for 45UV5,.\n 46-56 Quartz magnifying lens for 45UV3, (1\" dia.).\n 46-58 Quartz (1”dia.) lens for 60-1290 union.\n 60-302 Swivel mtg. adapter, 1/2\" NPT for 48PT1, 48PT2, UV1A.\n 1/ \" union with Pyrex window for 48PT1, 48PT2.\n 60-801 2\n 60-1199-1 Coupling with quartz window, 1\" NPT for 45UV2, 45UV3, 45UV5.\n 60-1199-2 Coupling with quartz window, 1\" BSP for 45UV2, 45UV3, 45UV5.\n 60-1257 Union with quartz window, 1/2\" NPT for UV1A.\n 60-1290 Union with quartz lens, 1/2\" NPT for UV1A.\n 60-1664-3 Swivel mount adapter, 1\" NPT for 45UV5 scanners.\n 61-436 Lens cap (standard) for 48PT scanners.\n 61-2914 Shutter and bracket assembly only for 45UV5-1009.\n 61-3263 Shutter, bracket and lens assembly with lens holder and gasket for 45UV5-1005-1009,\n 1105 (includes a 61-2914).\n 82-95 Lens holder for 45UV5 scanner.\n 92-45 Quartz window used in 45UV3-1050 and 60-1237 union.\n 92-48 Quartz window used in 60-1199 union.\n 124-13 “O” Ring used in 60-1199 union.\n 124-14 “O” Ring used in 60-801, 60-1257, 60-1290.\n\n\n\nRemove power from the control and remove the control from its wiring base before\nproceeding.\n\n\n\n\n 3\n\f \n\n\n\n\nINSTALLATION\n The amplifier modules are used with the Fireye\n Modular 3G-OTH-02818 Base Chassis (P/N MEC120,\n MEC120C, MEC120R, MEC120D, MEC120RC\n for 120VAC, P/N MEC230, for 230VAC). They\n are installed in the chassis by grabbing hold of the\n amplifier module by the edges of its printed cir-\n cuit board, aligning the module with the guide\n slots on the opening in the middle of the chassis,\n and inserting the module into the pin connectors.\n The amplifier modules are designed to fit in the\n proper slot only. DO NOT FORCE THEM.\n\n\n\n 12\n\n 11\n\n 10\n\n\n 9\n\n\n\n\n AMPLIFIER TEST JACK VOLTAGE\n 8\n\n 7\n\n\n 6\n CORRELATION BETWEEN\n 5…
