Fireye Flame-Monitor EP Programmer Modules. The Fireye programmer modules—including EP100S

[{"filename":"EP380-SPEC-Flame_Monitor_Programmer_Modules_EP380_English_2013-06-01.pdf","text":"SPECIFICATION DATA\n EP380 PROGRAMMER MODULE\n\n\nFeatures\n\n• Selectable Operation. The dipswitches allow\n easy replacement of the EP260, EP261 (Extended\n MTFI), EP270 (Early Spark Termination), and\n EP265 (Pilot Stabilization) programmers.\n\n• Selectable Purge Timings. Purge Timings easily\n selectable from 30 seconds to 30 minutes using\n dipswitches.\n\n• Air Flow Proven Open To Start. This feature\n can be enabled or disabled using the dipswitches.\n\n• Compatible with ED510. Use with the display\n module ED510. (See Bulletin ED-510-SPEC for\n more information.)\n\n• Backward compatible. Easy to upgrade with all\n existing FLAME-MONITOR controls.\n\n• Continuous Status Indication. as well as diag-\n nostic information.\n FLAME-MONITOR System and incorporates a plug-\nApplication in design for ease of installation. It is micro-processor\n based that provides a continuous readout of the oper-\n The Fireye EP380 Programmer Module is used ating status of the FLAME-MONITOR control. It\nwith the FLAME-MONITOR™ Burner Management also stores the burner cycle and on-time history, lock-\nControl System (P/N's E100 and E110). The EP380 out history (with burner cycle and burner hour time\nprovides start-up programming, safe start check, and stamp) that is accessible with the ED510 alpha-\nflame monitoring supervision. It insures proof of low numeric display or E500 Communication Interface. If\nfire position, and fuel valve end switch safety checks. replaced, the new programmer card will begin accu-\nThe control is designed to initiate a safety lockout if mulating a new history.\nany of these circuits open at the improper point in the\ncontrol cycle. A running interlock circuit on the\nFLAME-MONITOR system constantly monitors the Ordering Information\nlimit switches, air flow switches, and fuel pressure\nswitches through the programmer. A modulator (fir- The EP380 Programmer module with selectable\ning rate motor) circuit is not provided on the EP380 operation is used to replace EP380, EP381 (15 sec-\nProgramer Module. ond purge), EP382 (1 second purge), and EP390 (90\n The programmer module will de-energize all fuel second purge) programmer modules.\nvalve circuits within four (4) seconds (max.) follow-\ning a flame failure or at the end of the pilot trial for\nignition period if no flame is detected. An alarm cir-\ncuit will be energized following a safety lockout.\n The EP380 programmer is the heart of the\n\n EP-380-SPEC\n\fDescription of Dipswitch Functions\n\n DIPSWITCH POSITION\n U = UP DN = DOWN\n FUNCTION\n 1 2 3 4 5 6\n Dn Recycle on 3-P Open\n Up Non Recycle on 3-P Open\n\n Dn 15 Sec Post\n Up 10 Sec Purge\n\n Dn Dn Dn 30 sec.— EP380\n Dn Dn Up 1 sec.— EP382\n Dn Up Dn 5 sec. Selectable High Fire\n Purge Timing\n Dn Up Up 15 min. — EP381\n Up Dn Dn 90 min.— EP390\n Low Fire Purge Timing\n Up Dn Up 2 min. 30 sec. (min.)\n Up Up Dn 5 min.\n Up Up Up 10 min.\n Dn Prove 3-P Open DISABLED\n Up Prove 3-P Open ENABLED\n\n\n\n\nTiming Chart for EP380\n Refer to Bulletin EP-3801 for dipswitch settings and timing charts of EP380 configured as\n EP381 (15 second purge), EP382 (1 second purge), and EP390 (90 second purge).\n\n\n\n\n Type EP380\n SELECTABLE OPERATION (RECYCLE OR NON-RECYCLE) RUNNING INTERLOCKS (3/P)\n PURGE TIME - 30 SEC.1 FLAME FAILURE RESPONSE TIME 4 SEC.\n PROGRAMMING SEQUENCE\n LFS FIRING\n L1/13\n CLOSED L1/13\n ON\n T M\n E PURGE 1 SEC1 POST PURGE2\n R MINIMUM 15 SEC\n M X* PTFI\n I\n N 5\n A PTFI MTFI\n L\n 6\n 7\n * TERMINAL “X” USAGE REQUIRES JUMPERING “5” & “10” ON THE WIRING BASE\n\n\n\n\n FIREYE EP-380-SPEC\n 3 Manchester Road JUNE 2013\n Derry, New Hampshire 03038 supersedes February 1994"}]