Suntec PUMP OL – SOLENOID SINGLE STEP PUMP

[{"filename":"OL_US_Ed7_nov-2024-1.pdf","text":"SOLENOID SINGLE\n STEP PUMP\n OL\nThe SUNTEC OL oil pump incorporates a blocking solenoid valve with in-line OL - US - Ed. 7 - November 2024\ncut-off function.\nCOMPATIBILITY PUMP\n IDENTIFICATION\n- Fuel oil #2 and lighter, special \"V\" models for B6-B100 (blends from 6%\nup to 100% biodiesel, per ASTM D396) and \"K\" models for Kerosene. (Not all model combinations are available\n Consult your Suntec representative)\n- One or two-pipe system.\n OL: pressure regulation and blocking\n solenoid valve with in-line cut-off function\nPUMP OPERATING PRINCIPLE\n V : B6-B100 applications\nThe gear set draws oil from the tank through the built-in filter and transfers it\n Gear set capacity\nto the nozzle line via the cut-off solenoid valve . A pressure regulating valve is (see pump capacity curves)\nused to by-pass all oil which is not required at the nozzle.\n Shaft rotation and\nOne-pipe installation nozzle location\nThe oil which does not go through the nozzle line is returned directly to the (seen from shaft end)\ngear inlet and the suction line flow is equal to the nozzle flow. In that case, the A: clockwise rotation/\n right hand nozzle.\nby-pass plug must be removed from the return port, and the return port sealed B: clockwise rotation/\nby steel plug and washer. left hand nozzle.\nTwo-pipe operation C: anti-clockwise rotation\nThe by-pass plug is fitted in the return port, which ensures that the oil by-passed left hand nozzle.\n D: anti-clockwise rotation\nby the regulating valve is returned to the tank and the suction line flow is equal right hand nozzle.\nto the gear set capacity.\n K: kerosene applications\nCut-off\n Pump series\nThe solenoid valve of the OL pump is of the \"normally closed\" type and is 1: conical thread\nsituated in the nozzle line. This design ensures extremely fast response and 4,5,6 : cylindrical thread\nthe switching can be selected according to the burner operating sequence and Model number\nis independent of motor speed.\nWhen the solenoid is : OL V 35 C K 9 1 xx 1 P 06\n- non-activated, the valve is closed and all oil pressurized by the gear set\n Revision number\npasses through the regulator to suction or the return line, depending upon\n Installation\npipe arrangement.\n P : by-pass plug inserted in return port\n- activated, oil passes to the nozzle line at the pressure set by the pressure for two-pipe operation\nregulating valve. M : without by-pass plug,\nBleed return plugged,\n for one-pipe operation\nIn one-pipe operation, the bleeder valve must be loosened ( or a pressure port Solenoid valve voltage\nmust be opened) until the air is evacuated from the system. 02 : 24 V AC\nBleeding in two-pipe operation is automatic : it is assured by a bleed flat on 06 : 110-120 V AC\nthe piston. 05 : 220-240 V AC\n\n\n Solenoid valve Solenoid valve\n (NC) (NC)\n closed open\n\n\n\n\n Pressure\n to nozzle adjustment\n\n\n\n\n Pressure port Back\n Gear set or bleeder valve to suction\n Shaft seal\n\n\n Oil under suction Inlet or\n vacuum\n Oil under pressure gauge port By-pass By-pass\n plug plug\n By-passed oil inserted removed\n returned to tank\n TWO PIPE ONE PIPE Return\n or to suction Suction Return INSTALLATION INSTALLATION plugged\n\n\n Suntec Industries Incorporated - 60 Aberdeen Drive - Glasgow, KY 42141 - USA\n Tel : 270 651 7116 - www.suntecpumps.com\n\f Hydraulic data\nTECHNICAL DATA\n Gear size Nozzle pressure range Factory setting*\n General 35/55 60 - 260 or 120 - 210 psi @5 cSt 200 or 175 psi\n 65/95 145 - 175 psi @5 cSt 175 psi\n Mounting Flange mounting\n 35K/55K/65K (Kerosene 120 - 210 psi @ 1,8 cSt 175 psi\n Hub mounting available for OL 35/55/65\n models)\n Connection threads Conical : Cylindrical (according to ISO 228/1) : *other ranges available on request, refer to the specified range of the\n Suction and return 1/4 NPTF G 1/4 particular fuel unit.\n Nozzle outlet 1/8 NPTF G 1/8\n Operating viscosity 2 -12 cSt for OL 35/55/65/95\n Pressure gauge port 1/8 NPTF G 1/8\n Vacuum gauge 1/4 NPTF G 1/8 1.25 - 12 cSt for OL 35K/55K/65K\n Oil temperature 32 - 140°F in the pump\n Valve function Pressure regulation\n Ambient temperature 32 - 140°F\n Strainer Open area : 0,93 in²\n Inlet and return pressures 10 psi max.\n Opening size : 5.90 mil\n NFPA limits pressures to 3 psi max\n Shaft 5/16 \" dia. Suction height Single pipe : 6\" Hg max. vacuum,\n Two-pipe : 12\" Hg max. vacuum, to prevent air\n By -pass plug Inserted in return port for 2 pipe system; to be separation from oil\n removed with a 3/16\" Allen key for 1 pipe system. Rated speed 3600 rpm max.\n Weight 3.44 lBs Torque (@ 45 rpm) 0.88…