Combutech Pressure switch COMBUP150 5-150mbar

COMPACT PRESSURE SWITCH COB10002-10  CONTENT APPLICATION / FEATURES CHARACTERISTICS DIMENSIONS APPLICATION / FEATURES The COMBUPx compact pressure switch is specially designed for monitoring air or gas pressure in gas-fired equipment and systems, such as burners. • It allows for effective monitoring of pressure in gas pipelines. • Its compact size makes it very easy to install, even in confined spaces. • Thanks to its ergonomic structure, the user can adjust the operating parameters himself. • It is available in several versions, offering different pressure settings to suit various installation needs. • COMBUPx can be configured as minimum or maximum pressure switches, depending on system requirements. • The set point is adjustable up to 500 mbar, independent of the range effective. • It can operate under a continuous working pressure of up to 600 mbar. • It is compatible with gases of families 1, 2 and 3, as well as with other neutral gases non-corrosive. • Fully compatible with other similar products, it integrates easily into existing systems. FEATURES Kind Adjustable Body Cast aluminum Materials Diaphragm HNBR Switching contact Ag-SnO2 Setpoint adjustment Rotary graduated knob Working temperature: -15 ~ +60 ÿ, Temperature Storage temperature: -20~+80 ÿ Min. AC efficiency 24 V max. 250 V Switching voltage DC min. 24 V max. 48 V Cutting power 6A AC max Electrical power AC eff max. 6 A for cos 1 AC eff max. 2 A for cos 0.6 AC eff min. 20 mA Switching current DC max. 1 A DC min. 20 mA Kind Gases family 1, 2 and 3 according to EN 437+A1:2009; Air 02  FEATURES Model COMBUP3 COMBUP10 COMBUP50 COMBUP150 COMBUP500 1.0 ~ 3.0 2.0 ~ 10.0 5.0 ~ 50.0 5.0 ~ 150.0 100 ~ 500 Pressure range (mbar) The COMBUP150 may deviate slightly from the setting tolerance in the range of 5.0 to 30 mbar Factory setting (mbar) 1.0 2.0 5.0 5.0 100 ÿ1.0 mbar ÿ1.5 mbar ÿ 3.0 mbar ÿ 6 mbar ÿ 20 mbar Differential pressure (ÿP)max Allowable pressure (mbar) 500 (50 kPa) 600 (60 kPa) Terminal - 800 VAC/1 min Rigidity Terminal dielectric Terminal - 1500 VAC/1 min Earth Insulation resistance 100ÿ , Min. DC500V Megger Adjusting the tolerance to ± 15% deviation between the switching point and the setpoint, which adjusts the pressure point in room temperature the event of a pressure drop when the membrane is in the vertical position. Allowable deviation Permissible deviation from the set value ÿ ± 15% during the service life test according to EN 1854 Electrical connection 3-pin connector according to DIN - EN 175 301 - 803 (without earth connection). Pressure measurement ø 9, length 10 mm, with threaded cap (test tip integrated in a ø9 metal housing) Process connection Standard: Centered on the bottom of the case, 1/4'' Female thread Degree of protection IP 54 according to IEC 529 (EN60529) Leak ÿ Sealing Pmax X1.5 for 1 minute or Standard (EN1854 (7.2.2) The operating pressure drift must be within ± 15% before and after the endurance test. Drift Guarantee 1 year Noticed In the following cases, we recommend that you contact us before use. 1. Use only sufficiently cured silicone tubes. 2. Vapors containing silicone may impair the operation of electrical contacts. In case of low switching capacities, e.g. 24 V, less than 20 mA, we recommend using an RC module or an electronic switch (non-contact switch) in air containing silicone or oil. 3. A fall or impact may compromise the safety functions. These products must not be put into service, even if they show no damage. 4. In case of high humidity or aggressive gaseous components (H2S), we recommend using a pressure switch with gold contact. 5. Closed-circuit current monitoring is recommended under severe operating conditions. 6. Do not operate at a pressure lower than the minimum set pressure. 03  Connection diagram Minimum pressure switch When the pressure falls Maximum pressure switch When the Function below the set value, NO opens and NC closes pressure exceeds the set value, NC opens and NO closes when used as... Connection by connector according to DIN 43650 Installation position Standard installation position If a different installation position is used, be careful at modified operating points When installed horizontally, the pressure switch switches to the highest pressure. When installed horizontally above the head, the pressure switch switches to the lowest pressure. When installed in an installation position intermediate, the pressure switch switches to the highest pressure high. 04 DIMENSIONS Fig 1. Gas pressure switch (V) 05 PRESSOSTAT COMPACT COB10002-10  CONTENU  APPLICATION / FONCTIONNALITÉS  CARACTÉRISTIQUES  DIMENSIONS APPLICATION / FONCTIONNALITÉS Le pressostat compact COMBUPx est spécialement conçu pour la surveillance de la pression de l’air ou des gaz dans les panoplies et les équipements à gaz, tels que les brûleurs. • Il permet de surveiller efficacement la pression dans les canalisations de gaz. • De taille compacte, il est très facile à installer, même dans des espaces restreints. • Grâce à sa structure ergonomique, l’utilisateur peut ajuster lui-même les paramètres de fonctionnement. • Il existe en plusieurs versions, offrant différents réglages de pression pour répondre à divers besoins d’installation. • Les COMBUPx peuvent être configurés comme pressostats de minimum ou de maximum, en fonction des exigences du système. • Le point de consigne est ajustable jusqu’à 500 mbar, indépendamment de la plage effective. • Il peut fonctionner sous une pression de service continue allant jusqu’à 600 mbar. • Il est compatible avec les gaz des familles 1, 2 et 3, ainsi qu’avec d'autres gaz neutres non corrosifs. • Entièrement compatible avec d'autres produits similaires, il s'intègre facilement dans des systèmes existants. CARACTÉRISTIQUES Type Réglable Corps Fonte d'aluminium Matériels Diaphragme HNBR Contact de commutation Ag-SnO2 Réglage consigne Bouton gradué rotatif Température Température de service : -15 ~ +60 ℃, Température de stockage : - 20 ~ +80 ℃ Efficacité CA min. 24 V max. 250 V Tension de commutation CC min. 24 V max. 48 V Pouvoir de coupure 6A AC max Puissance électrique AC eff max. 6 A pour cos 1 AC eff. max. 2 A pour cos 0,6 Courant de commutation AC eff. min. 20 mA DC max. 1 A DC min. 20 mA Type Gaz famille 1, 2 et 3 selon EN 437+A1:2009 ; Air 02  CARACTÉRISTIQUES Modèle COMBUP3 COMBUP10 COMBUP50 COMBUP150 COMBUP500 1,0 ~ 3,0 2,0 ~ 10,0 5,0 ~ 50,0 5,0 ~ 150,0 100 ~ 500 Plage de pression (mbar) Le COMBUP150 peut s'écarter légèrement de la tolérance de réglage dans la plage de 5,0 à 30 mbar Réglage d'usine (mbar) 1,0 2,0 5,0 5,0 100 Pression différentielle (△P)max ≤1,0 mbar ≤1,5 mbar ≤ 3,0 mbar ≤ 6 mbar ≤ 20 mbar Pression admissible (mbar) 500 (50 kPa) 600 (60 kPa) Terminal - Rigidité 800 VCA/1 min Terminal diélectrique Terminal -…